X2 Premium HD June 27 Official release - Discussion

[cpr43]

No audio on TVU AAC 11973 H 27500 Hispasat 30w as well. Used to work fine before

[rrob311]

"My satellite channel list stayed intact for the first time in months with the new firmware. I am hoping that the previous firmware caused this problem. I am going to load as many satellites as I can tonight and see what happens."

rrob311, if you're referring to the sat list that pops up when you press the sat button and you're using an older DB with the new firmware, you'll find that 27 sats is still the limit.

I still haven't finished scanning with a clean DB to see if the 27 sat limit has been rectified.

Yes, when I press the SAT button all of my satellites are staying. Only managed to scan 15 last night but I am happy with it. I can now hunt for feeds again and watch my favorite channels.

[crosspaws]

Same hear, W/AMC7 I thought this was a promising FW but the audio problem is a big problem. Does YouTube work?

[el bandido]

YouTube works for me.

[cpr43]

No audio on TVU AAC 11973 H 27500 Hispasat 30w as well. Used to work fine before

You Tube works on my side but NO audio at all too. Something is wrong with the audio feature. Roll back to April 9th audio on both working fine

[crosspaws]

Went back to April 9 FW nice that my sat list stayed together. As it turns out only some YouTube videos like Psy (which is the first one on my screen) go to loading and never plays. Other wise it works fine. It still the best FTA box I have used and use!

[rrob311]

I noticed when I switch satellites from my motorized dish to 97w which is a fixed dish on another port, my motor gets commanded to move. The motor setting is set to none. It would be nice to get that fixed.

[ViP3R]

No mention of audio/video info?

Costa they informed me that they did apply the video info on the channel bar and sent me a picture, see attached..A factory default should be done after the upgrade to apply the new settings.
Remember to save/backup your settings and channel info..

[Only registered and activated users can see links. ]

[Only registered and activated users can see links. ]

Also for other issues such as...."When editing a sat name, after saving, it will randomly freeze requiring a reboot." we did the test many times and no issue like this and also after upgrade must make factory default to apply the new setting.

They will try their best to issue the new software next week to solve the motor bug and also AAC Audio.

On another note by Rob I think..

Sats scanned are still displayed in random order when the sat button is pressed, even though they were scanned by orbital position." Can you please provide more details to us because this issue is not clear ?

So I would ask all to do a Factory default after the upgrade and see if some of these reported issues are still present... Remember Backup first..

[eastof111]

"Also for other issues such as...."When editing a sat name, after saving, it will randomly freeze requiring a reboot." we did the test many times and no issue like this and also after upgrade must make factory default to apply the new setting."

This happened to me after renaming some sats. I did not reboot after renaming many sats. Maybe I should have, and then continued the renaming process. It might not have caused the receiver to freeze.

"Sats scanned are still displayed in random order when the sat button is pressed, even though they were scanned by orbital position." Can you please provide more details to us because this issue is not clear?"

See attached before and after pictures. Started my scan with a clean DB, new firmware and factory reset to be sure there were no conflicts. First sat scanned was 45º and continued to 113º when I had to stop.

[ViP3R]

"Also for other issues such as...."When editing a sat name, after saving, it will randomly freeze requiring a reboot." we did the test many times and no issue like this and also after upgrade must make factory default to apply the new setting."

This happened to me after renaming some sats. I did not reboot after renaming many sats. Maybe I should have, and then continued the renaming process. It might not have caused the receiver to freeze.

"Sats scanned are still displayed in random order when the sat button is pressed, even though they were scanned by orbital position." Can you please provide more details to us because this issue is not clear?"

See attached before and after pictures. Started my scan with a clean DB, new firmware and factory reset to be sure there were no conflicts. First sat scanned was 45º and continued to 113º when I had to stop.

Thanks bro..I will pass on the images you took...