Just an update on how the 6' mesh install went. I'm receiving about 10% less signal quality on the ku side which is normal in comparison to a solid dish. Most c band sats scan in but only the strong tp have enough signal quality to watch the channels and of course no s2. I have a bsc621-2 universal lnbf as my feed but I'm not too happy with it. I'm going to swap it out with my neighbours wsi 741 c/ku lnbf and see if I can improve signal quality. Im trying to hunt down a geosat ck1 lnbf as I've always had more success with their lnbfs. My new arc is 30-129w as I put the actuator on the right side(only up to 101w on the left side). The 8' solid is arriving on Wednesday but I'll leave that install for Spring with a new pole and more of a seperation from my 10' bud.
Thread: 8'Fortec
Results 21 to 30 of 59
-
Guest Guest11-13-2011,07:21 AM
-
Guest Guest11-15-2011,03:18 PM
Another update on the 6' mesh install. I tried my neighbour's wsi741 but it turned out to be even worse then the bsc621 so I slapped that one back on. After a couple of hours, changing my elevation on my south sat at 74w and my east at 30w and my west at 125w- we achieved success. My ku side is even stronger then on the 6' solid and I'm scanning in about 80% of all c band tp as well. I ordered the new ESX741 c/ku lnbf but it hasn't reached market yet- 1 to 2 months. My 8' solid will be arriving tomorrow and will be my Spring project- new pole and all.
Now that I've basically saved all sat positions and know the dish is doing well, I'm going to reset my limits on the positioner and start doing some intense scanning to see what c band sats I can get on the Atlantic side. I will also be posting the signal quality comparison to my previous post on the azbox.
-
Guest Guest
-
Guest Guest
-
Guest Guest03-23-2012,03:10 PM
Got a bit bored this afternoon so I decided to start digging. I'm at 2' at the moment and enough for today. I'm going to rent some kind of post digging tool tomorrow and finish this one off. First 2' are always the easiest, I hope I don't hit any big rocks the next 2' down.
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Kiss My Assrrob311 liked this post
-
03-23-2012,05:27 PM
Good to hear you got it started, bud. Hopefully the rest of the digging goes well.
Optibox Anaconda, X2, OpenBox-S9, CS8000 and 2 X CW700S, 7 1/2' Perfect Ten scanning 55W to 139W C Band and a 39" Q-Sat scanning 30W to 125W Ku Band
-
-
03-23-2012,06:19 PM
Never thought to mention, Costa, I own a 12", 3 point hitch post hole auger if you have access to a tractor that can handle it.
Optibox Anaconda, X2, OpenBox-S9, CS8000 and 2 X CW700S, 7 1/2' Perfect Ten scanning 55W to 139W C Band and a 39" Q-Sat scanning 30W to 125W Ku Band
-
Guest Guest
-
Guest Guest03-24-2012,08:54 AM
Finally got it done, I'm really tired right now. I hit a couple of big rocks at about 2 1/2' which took some time to remove. Relief after 3' when I think I hit some crushed stone and some of the builders original stone. I would have gone to 4 1/2' but my pole digger was only 4'. I'm at about 3' 10" which will do fine. Picking up the concrete on Monday and the pole on Wednesday- should have this puppy installed and scanning by the first week of April.
[Only registered and activated users can see links. ]