TNAP-5 Image Discussion

[el bandido]

Last question for this year: Will moded AVL6261 T2MI driver work on osmio mini4k too ?

NO. Not this year.....
Because the enigma2 has not been modified to accept the signal-below-lock changes. Wait until next year.

[el bandido]

Last question for this year: Will moded AVL6261 T2MI driver work on osmio mini4k too ?

Do the following if you want it to work:
(1) Do an online update (Main menu--->Setup---> Software update)
(2) Go to Plugins and select Download Plugins (Main menu--->Plugins, then press green remote button)
(3) Navigate to extra plugins and pres the OK button on the remote to enter. Select and install enigma2-plugin-extra-t2mi-module-tnap-mod_5.15.0

[el bandido]

[Only registered and activated users can see links. ]

Do the Exact same thing::
(1) Do an online update (Main menu--->Setup---> Software update)
(2) Go to Plugins and select Download Plugins (Main menu--->Plugins, then press green remote button)
(3) Navigate to extra plugins and pres the OK button on the remote to enter. Select and install enigma2-plugin-extra-t2mi-module-tnap-mod_5.15.0

Your test image has extended frequencies that we cannot use. These extended frequencies mess up the Ku blindscan. Follow the instructions above for best results.

[stephan94]

I think the version i tried was already with the plugin avl6261 T2mi 700mhz europe
because I didn't load any plugin to get all my positive results

[stephan94]

here the result of a blindscan which found a tranponder of sr 940 ( 23,5 East)

[el bandido]

I think the version i tried was already with the plugin avl6261 T2mi 700mhz europe
because I didn't load any plugin to get all my positive results

You were sent a test image.
Do an online update then load the plugin avl6261 T2mi 700mhz europe

[cyberham]

...Your test image has extended frequencies that we cannot use. These extended frequencies mess up the Ku blindscan. Follow the instructions above for best results.

Updated. This might explain the slow blind scans yesterday with the test image. Their results were accurate but slow. After updating just now, I blind scanned 87W Ku and it found every single transponder in just 3:43.

The Positioner Setup with 2 decimal places plus the non-locked SNR readout make the Edision a DX-hunter's delight now.
[Only registered and activated users can see links. ]

[lme]

After today's update, tnap5-mod worked ok. turned the box off for few hours, and now i couldn't get a signal !!!
after i booted on regular tnap5 slot and booted back to tnap5-mod slot, it got signal !!!
now i scanned 121w-cband, but it did not find any active tps, despite the fact that 3 tps are showing signals (see pics from texas lottery ch):

[Only registered and activated users can see links. ][Only registered and activated users can see links. ][Only registered and activated users can see links. ][Only registered and activated users can see links. ]

[el bandido]

What is the information for the 3 transponders that have a signal and show channels? My MIO gets nothing on a blindscan of 121w. My Octagon SF8008 found One empty data transponder and nothing else. Which one of your receivers blindscans these transponders and channels successfully?

[Only registered and activated users can see links. ]

[lme]

osmio4k+ stb, with tnap5, finds:
[Only registered and activated users can see links. ][Only registered and activated users can see links. ][Only registered and activated users can see links. ]

same stb, with tnap5-mod finds same tps, but does not lock on "MIS" tps:

[Only registered and activated users can see links. ][Only registered and activated users can see links. ][Only registered and activated users can see links. ]

the ch on tp 4151H is a feed, broadcasting at certain hours only.