Thread: Sat list

Page 1 of 4 1234 LastLast
Results 1 to 10 of 35
  1. Collapse Details
    Sat list
    #1
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    619
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    Got my VU+ Zero 4k today.
    what program do I need to edit the sat list and how do you get it from the box to the computer for editing. usb stick?
    I'm lost. lol
    Thanks!
    Reply With Quote
     

  2. Collapse Details
    #2
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,191
    Post Thanks / Like
    Congratulations!
    You are not lost. What are you wanting to do with the satellite list? It might help to describe your satellite antenna setup in detail. The receiver is not hard to setup, but of course you have to know how.
    Reply With Quote
     

  3. Thanks Megatron817 thanked for this post
  4. Collapse Details
    #3
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    619
    Post Thanks / Like
    Just need to add north american sats. I don't see how to add a sat or add a tp.
    yeah I just don't know how. and how would you add pid's to a tp.
    Maybe i havn't found the right menu.
    Thanks
    Reply With Quote
     

  5. Collapse Details
    #4
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,191
    Post Thanks / Like
    What image is in the receiver?

    DreamboxEDit is one of many satellite editors, or you can telnet into the box and edit the satellite file using any .xml editor.

    I can help you set the box up and get it running, but this will be very hard to do without knowing the antenna settings you are using.

    Channel PIDS can be added by using telnet and manually adding them to the channel file which is named lamedb. I think you can also add PIDS using DreamboxEDit. Would help to know what PIDS are you wanting to add.
    Reply With Quote
     

  6. Thanks ViP3R thanked for this post
  7. Collapse Details
    #5
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    619
    Post Thanks / Like
    30" multi sat dish aimed at 97w ku with 2nd lnb pulling in 103w ku 4 way discq switch, port 1 97w port 2 103w
    a lot of radio on 103w has to have the pid's added manually.
    I seen how to set up the antenna settings but there just were not any sats that i use.
    I connected with open Webif ealier I think it said 11-23 -17 experimental was the firmware.
    Reply With Quote
     

  8. Thanks el bandido thanked for this post
  9. Collapse Details
    #6
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,191
    Post Thanks / Like
    OK.

    Do you understand how to use telnet and transfer files using FileZilla or other ftp program?

    Do you understand how to flash the receiver or load an image (Main firmware)?

    What is the resolution for your television? 1080p?
    Reply With Quote
     

  10. Collapse Details
    #7
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    619
    Post Thanks / Like
    NO
    NO
    My old ps3 plays 1080p fine but I just set the VU+ 4k to 720p for now.
    Let me go to you tube see if I find any thing on the telenet and file zilla.
    Thanks
    Reply With Quote
     

  11. Thanks el bandido thanked for this post
  12. Collapse Details
    #8
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,191
    Post Thanks / Like
    You have given enough information to setup an image that will run. I will upload a file to the internet for you in probably 30-40 minutes. That should get you going.
    Reply With Quote
     

  13. Thanks Megatron817 thanked for this post
  14. Collapse Details
    #9
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,191
    Post Thanks / Like
    (1) Download file in link.
    (2) Put file on a good, usb stick or pen drive.
    (3) Unzip or extract file once. This should give you a vuplus folder.
    (4) Turn power off to Zero 4K using rocker switch on back of receiver.
    (5) Insert usb stick with extracted file into the rear usb port. Power the receiver ON.
    (6) The front Vu+ emblem or light will blink or flash slowly. Wait for the front light to blink or flash fast (usually 3-5 minutes).
    (7) Power Off unit using rocker switch on back of the receiver and remove usb stick.
    (8) Power ON using rocker switch and wait for receiver to boot. This should take no longer than 5 minutes.

    After booting completes:
    Press the green remote button once for the channel list, and twice to display the two satellites.
    Use the radio or tv buttons on the remote to change between tv and radio channels.
    The ip address in the receiver will need to be changed for your network.
    Connect the receiver to the internet and set time zone for correct time display.

    Note: The Zero 4K uses a force update. Remove the usb stick and delete the vuplus folder. You may save the zipped file as the receiver cannot "see" it.

    [Only registered and activated users can see links. ]
    Reply With Quote
     

  15. Thanks Megatron817, ViP3R thanked for this post
  16. Collapse Details
    #10
    Join Date
    Mar 2018
    Location
    West Central Florida
    Posts
    619
    Post Thanks / Like
    Does the usb drive need to be formated fat32 or what?
    Can't seem to get it to work.
    Thanks
    Reply With Quote
     

Page 1 of 4 1234 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •