Does the Atemio have blind scan?
Get comfortable transferring files because I have several that should work such as on-board channel, sat and pid editors.
I think diseqc 1.2 positions will go way over 100 positions in Enigma 2. You will need to enter all your antenna settings one time, then you can copy and save them to transfer to future images. The antenna settings can be transferred to a different image or even a different receiver as long as it is running an Enigma 2 image. I think you will really enjoy the receiver and the operating system once you become familiar with it.
Thread: Nemesis start up challange
Results 21 to 30 of 152
-
10-31-2014,07:37 PM.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
10-31-2014,08:09 PM
Yes it has blind scan. So far I have only used manual scan for one TP. It did it in a few seconds. I will start working on clearing the Euro stuff and loading your N.A. sat list. Later I will want to try your other files as I get to know the system.Wife went to bed, I'm back up after a short nap and ready to try a few things. I'm still recovering from my knee transplant (gets a little better each day) so everything is happening in slo mo.
C: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
10-31-2014,08:23 PM
Take your time. You have been through quite an ordeal.
There is not much of a risk of bricking the receiver by transferring or changing files in the receiver's operating system. About the worst that can happen is you have to reload the image and start over. So make backups often so you will have a restore point!
The antenna settings reside in etc/enigma2. The name of the file is settings. You have a large antenna system, so you will want to copy and keep the settings file in etc/enigma2 once you have correctly entered all of the satellites. The Engima 2 operating system allows you to use a multitude of antenna settings, so I doubt you have any problems like you experienced trying to set up the Optibox Raptor..
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
11-01-2014,03:19 AM
Always remember to place enigma into sleep mode before transferring live files as they are very sensitive and prone to corruption when transferred while enigma is live.
-
11-01-2014,07:26 AM
That is a good idea but it I rarely if ever do that. All I do is let the box idle. Don't try to change channels or do anything else with the box while transferring files has worked fine for me. Zero problems so far.
Anyway, Aren't the telnet commands init3 to sleep & init4 to wake?.
.
.
Meine Dreambox One ist ein Stück Scheiße!.
-
-
11-01-2014,09:17 AM
Thanks for the info PALE-RIDER, good to know.
PixL - here is a program that I use for enigma and transferring files, I use Filezilla in the past, I don't like it to many windows.
Regards.
Chewie
-
11-01-2014,11:30 AM
Well I'm stuck in a boot up loop now. I had done a factory reset, removed the existing satelites.xml and replaced it with EB's file. Looked thru the Nemesis menus and still see the Euro stuff. Reboot and reinstall 4.2 again, now keeps loading from 51% to 100% over about 5 times, then sits there for several minutes, then loadong again 51-100%. Can't change any screen.
C: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
11-01-2014,11:35 AMC: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
4:2:2 AZminiMe slaved off C/Ku
-
11-01-2014,11:50 AM
Did the receiver display what is described in step 11 when you reloaded the image?
1) - Turn off the decoder;
2) - Disconnect any peripherals connected to the USB port on the front and rear;
3) - Format a USB memory stick from your PC in fat32;
4) - Download the latest version of firmware available;
5) - Unzip the zip or rar file;
6) - Copy the folder "atemio" on the USB stick;
7) - Insert the memory stick into the front USB port of the decoder (open the flap that covers cam / card);
8) - Turn on the decoder by rear panel;
9) - The display will show "VOL + to upgrade" for a few seconds;
10) - Press the arrow up in the front panel of the decoder;
11) - You will see step by step in the display: "Flashing SPLASH", then "Flashing KERNEL", then "Flashing ROOTFS" (this takes a couple of minutes), and then "Complete! Reboot!" and restart: Wait until it reappears "VOL + to upgrade";
12) - The procedure is completed; turn off the decoder by rear panel;
13) - Remove the pen from the front USB port;
14) - Reconnect any peripheral or hub-and-USB port on the rear USB;
15) - Turn on the decoder according to the instructions of the setup wizard.