Results 1 to 9 of 9
  1. Collapse Details
    Please help Golden Media Hypercube
    #1
    Join Date
    Mar 2014
    Posts
    6
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    Device no longer responds to any thing
    Black screen of the device
    Just a word on the TV Hypercube
    Here the explanation for reform

    [Only registered and activated users can see links. ]

    Stage 7
    [Only registered and activated users can see links. ]
    I did not understand very well stage
    Please help
    Reply With Quote
     

  2. Collapse Details
    #2
    Join Date
    Feb 2012
    Posts
    7,247
    Post Thanks / Like
    Sorry about your receiver not working. I haven't done a uboot recovery yet since I haven't had the need to do so. Looking at the stage 7 picture, El Bandido wrote the following after he successfully recovered his Hypercube.

    "Here are my notes on uboot recovery:
    The 2 pin jumper is located next to the 4 pin connector that runs to the front usb port or to the front of the receiver.
    You need a pen drive that has a Known Good Hypercube image of your choice installed on it. You may insert the pen drive into the USB port before or after connecting the jumper. The usb pen drive Must Be installed before the boot bin is transferred!"

    If you still can't get your receiver to work, you might list a step by step recovery process you have initiated and their results.

    Good luck!
    Reply With Quote
     

  3. Collapse Details
    #3
    Join Date
    Dec 2010
    Location
    Calgary, AB
    Posts
    13,910
    Post Thanks / Like
    Moved to discussions...I hope you have success.

    click click b00m
    Reply With Quote
     

  4. Collapse Details
    #4
    Join Date
    Mar 2014
    Posts
    6
    Post Thanks / Like
    Device worked
    Traced all the stages
    After the success of retrieval device
    Enigma2 the word on the screen of the device
    On television hypercube
    Reply With Quote
     

  5. Collapse Details
    #5
    Join Date
    Feb 2012
    Posts
    7,247
    Post Thanks / Like
    I think you are saying you went through the complete uboot recovery process and now all you get is the Hypercube logo on the tv screen. If so, I would redo the recovery process again until the receiver accepts the firmware via the recovery process.

    Sometimes the recovery process needs to be repeated a few times before the receiver will respond. This applies to most receivers, not just the Hypercube.
    Reply With Quote
     

  6. Collapse Details
    #6
    Join Date
    Mar 2014
    Posts
    6
    Post Thanks / Like
    All are now fully
    Device worked 100/100
    The operation succeeded
    Thank you for your cooperation brothers
    Reply With Quote
     

  7. Collapse Details
    #7
    Join Date
    Mar 2014
    Posts
    6
    Post Thanks / Like
    Another possible picture of the device Hypercube
    Reply With Quote
     

  8. Collapse Details
    #8
    Join Date
    Nov 2014
    Posts
    1
    Post Thanks / Like
    for me not u can to help me i am new and i followed all the steps and nothing made [Only registered and activated users can see links. ]
    Reply With Quote
     

  9. Collapse Details
    #9
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Read post #2 in this thread.
    Here is a Link:[Only registered and activated users can see links. ]
    If you have failure, list the results for each step.
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
    Reply With Quote
     

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •