Results 1 to 9 of 9
  1. Collapse Details
    openbox s9 hd pvr
    #1
    Join Date
    Jan 2013
    Posts
    5
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    no power to lnb checked f1 is ok replaced lm317t, power board has right voltage at all points don"t know what to check next.any ideas ? thanks box shows boot ,all works elsewhere
    Last edited by fewed; 08-31-2013 at 04:34 PM.
    Reply With Quote
     

  2. Collapse Details
    #2
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    How much DC voltage do you have at the receiver's lnb port? Check both polarities.
    By Chance, have you checked and made sure that lnb power is set to ON in the antenna setup menu?
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
    Reply With Quote
     

  3. Collapse Details
    #3
    Join Date
    Jan 2013
    Posts
    5
    Post Thanks / Like
    none at lnb port + or - yes checked more than once on settings . sorry my one b tton not working was p shing pretty hard k_ dish and lost lnb and motor power maybe throw in wb?
    Reply With Quote
     

  4. Collapse Details
    #4
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Maybe....
    Wait a couple of days first and see if anybody else here has an idea for you!
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
    Reply With Quote
     

  5. Collapse Details
    #5
    Join Date
    Jan 2013
    Posts
    5
    Post Thanks / Like
    ok and THANKS!!
    Reply With Quote
     

  6. Collapse Details
    #6
    Join Date
    May 2011
    Posts
    5,807
    Post Thanks / Like
    There are 2 capacitor to look for on the Power Supply, C19 and C17 and the 4 pin small IC SD4844. Also, it will help to change the poly switch F1993 from Digi key. All parts together less than 10 bucks
    X2 Premium III HD, Openbox X5/ S10, Gsky V3/V6, iSmart m100
    Reply With Quote
     

  7. Collapse Details
    #7
    Join Date
    Jan 2013
    Posts
    5
    Post Thanks / Like
    there is no c17 orc19 and the 4 legged ic isEL817 c209 if i read it right . as far as i can tell all leads from board have right voltage,looped o_t of pansat and it works that way
    Reply With Quote
     

  8. Collapse Details
    #8
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    With your volt meter check for lnb voltage on both legs of F1 (polyfuse) with coax dis-connected. If ok connect coax and check again. Post results in here.
    C: 8' Andrew w/orthomode feeding twin Norsat 8515, Atemio Nemesis
    Ku: 1.2m Channel Master w/orthomode feeding twin NJR universal lnbs, Manhattan
    DBS: Motorized DTV Slimline w/DMS 922 circular, Jynxbox Ultra V3
    4:2:2 AZminiMe slaved off C/Ku
    Reply With Quote
     

  9. Collapse Details
    #9
    Join Date
    Jan 2013
    Posts
    5
    Post Thanks / Like
    ok did I that, nothing lnb hooked,maybe .5v not hooked also nothing on LM317 this box is not 1 year yet so I think power board is a little diff. have been over all caps , have not taken to test yet maybe next step?
    Reply With Quote
     

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •