I tried to understand what X2 Premium Editor is but unfortunately I couldn't. Could anyone explain it to me in a simple way?. By the way, I only have NileSat on my box.
Any help would be appreciated.
Results 21 to 29 of 29
-
03-08-2014,02:36 AM
-
03-08-2014,08:18 AM
really shouldn't need it,if you load eurasian firmware the sat lists should be correct.
you may not even be able to load old firmware into the august version of the editor anyway.
You would have to use an older version.or am I being obtuse?
-
-
09-14-2014,04:24 PM
I've been trying to get this to connect my X2 Premium HD II with no success. Using Windows XP (and Windows 8.1), and a 9 pin null modem cable. All I get is connection time out messages. The software was installed as Administrator, no errors detected during installation. The cable works fine with my Fortec Lifetime Ultra and Channel Master, so I know the cable is good. Is there some kind of special COM settings needed in EZ-Manage Tool, or is a different type of serial cable needed? Or is there a third party software that can also connect to this receiver. THANKS!
GEOSATpro HDVR3500 (Fortec Star 90cm dish/Ku-band LNBF: aimed at 97.0°W, Wave Frontier Toroidal Dish w/multiple Ku-band LNBFs, aimed at 91°W, 95°W, 105°W, 113°W, 121°W, 125°W - Mini BUD: Primestar/ChannelMaster dish/C-band LNBF: receiving 97.0°W & 99.0°W
Other Toys: Mac mini (Early 2009) w/OS X El Capitan 10.11.4 Public Beta 7, iPhone 4S 64GB w/iOS 9.3 Public Beta 7, iPad 2 64GB (Wi-Fi/3G) w/iOS 9.3 Public Beta 7, AppleTV (3rd Gen) w/Apple TV Software 7.2.1, OS Build Version 8.4.1
-
09-14-2014,05:23 PM
click click b00m
-
09-14-2014,06:28 PM
any terminal program should show activity on the com port when you boot the receiver.
I assume the cable is the correct null modem.
like that
Code:BO Boot V2.7 Phase Scan in Boot Start Stage 200000 Phase Scan in Set Parameters Stage 31, 11, 15, 07, 07, 10, 24, 16, 16 [ 2 ff 2 0 ff ff ff ] 0x31 0x32 0x31 DDR2 DDR/PLL Init Done L2 cache Init Done Boot start SPI Load Code done CPUfreq 400000 DRAMSize 1024 BootManager V1.7 >> Pressing <space> key enter boot-menu. >> Load code from SPI... >> Check image parity... >> Unzip Image Start.... >> App Start... [cyg_net_init] Init: mbinit(0x00000000) [cyg_net_init] Init: cyg_net_init_devs(0x00000000) Init device 'eth1' [cyg_net_init] Init: loopattach(0x00000000) [cyg_net_init] Init: ifinit(0x00000000) [cyg_net_init] Init: domaininit(0x00000000) [cyg_net_init] Init: cyg_net_add_domain(0x80a0fdc8) New domain internet at 0x00000000 [cyg_net_init] Init: cyg_net_add_domain(0x80a0f85c) New domain route at 0x00000000 [cyg_net_init] Init: call_route_init(0x00000000) [cyg_net_init] Done Uart initialize Success init time1 interrupt init time2 interrupt init time3 interrupt init time4 interrupt
Last edited by dr.zin; 09-14-2014 at 06:36 PM. Reason: value added
or am I being obtuse?
-
09-15-2014,06:43 AM
it sounds like you are using the wrong version of editor for the version of firmware. The older editor only works with older firmware.
X2 M1 HD Mini ,X2 Premium II receiver, X2 Premium Mini (new edition), X2 premium III, QBox2 USB receiver, DSR406mn, Dsr922, DsR4200, SV360, 8 foot C-Band dish, 8 foot solid Ku dish and 3 foot Ku Dish, USBJAG NT cable & software
-
09-15-2014,10:32 AM
if I remember correctly there were 3 different versions of the editor but they all should make contact with the receiver,just not work 100% if not matched properly.
or am I being obtuse?
-
09-15-2014,11:41 AM
I have used all three and one does not work with newer firmware
X2 M1 HD Mini ,X2 Premium II receiver, X2 Premium Mini (new edition), X2 premium III, QBox2 USB receiver, DSR406mn, Dsr922, DsR4200, SV360, 8 foot C-Band dish, 8 foot solid Ku dish and 3 foot Ku Dish, USBJAG NT cable & software