Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 21
  1. Collapse Details
    #11
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    Contribute If you enjoy reading the
    content here, click the below
    image to support our site.
    Click Here To Contribute To Our Site
    I would think this receiver could easily do band-stacked. Just put in your lowest and highest freq. and set the scan for one polarity only.
    Reply With Quote
     

  2. Collapse Details
    #12
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    Today I got it to scan in 4 channels off my fixed dish 103Ku. This was done by letting it scan the existing TPs pre-programed in the sat list. Manual key in of a TP also works, blind scan still not working for me. Also can not get it to work with my C band dish. It send out a motor command, dish move to correct position, but no signal. Can someone with a ASS box take a look at my C band setup for 105w posted earlier in this thread, see if it looks the same as other versions of the AZbox.
    Reply With Quote
     

  3. Collapse Details
    #13
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    have you tried runnung straight to the c band dish without using any switches?
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
    Reply With Quote
     

  4. Collapse Details
    #14
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    Yes, still didn't work. I'm only running one switch in my system now, a diesqc 1.1 8 port, and the switching must be working because the AZ found my fixed 103Ku dish on port 4.
    My latest test was to use a splitter with the Raptor in command. I tuned in 89C where there are CBS 4:2:2 feeds. The Raptor gets the sound from the NFL game, but just a gray screen, plenty of signal. The AZ gets signal, but no channels will scan in manually or blind scan.
    Reply With Quote
     

  5. Collapse Details
    #15
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    I would expect you to get channels during a blind scan, even if the l.o. frequencies were wrong. You have the l.o.entered according to the instructions....

    What firmware is in the receiver? Maybe the firmware needs an update???
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
    Reply With Quote
     

  6. Collapse Details
    #16
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    Ver 1.0 Kernel 3.5.5

    The only ver available at this time
    Reply With Quote
     

  7. Collapse Details
    #17
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    Now it locked up after I tried to do a full manual key in of a TP including pids.
    This baby is not for me. I think I'm going to put it up for sale and move on.
    Reply With Quote
     

  8. Collapse Details
    #18
    Join Date
    Dec 2010
    Location
    Atlanta, Ga.
    Posts
    8,188
    Post Thanks / Like
    Send it back to the seller. Maybe you have a defective receiver?
    .
    .
    .
    Meine Dreambox One ist ein Stück Scheiße!.
    Reply With Quote
     

  9. Collapse Details
    #19
    Join Date
    Jul 2011
    Location
    Traverse City, Michigan
    Posts
    512
    Post Thanks / Like
    Yea, probably nothing defective except me. I just don't have the patience to struggle thru each little nuance. Maybe it would be a better fit for one of you E2 guys.
    Reply With Quote
     

  10. Collapse Details
    #20
    Join Date
    Oct 2012
    Posts
    26
    Post Thanks / Like
    Quote Originally Posted by el bandido View Post
    It would be better if they had some dedicated settings for bandstacked lnbs, but I have similar settings on a couple of receivers. Adjustable low and high settings for the lnb have allowed me to run a cband bandstacked Eagle Aspen, but I still had some problems with duplicate transponders & channels.
    I wish there was more support for bandstacked equipment because IMO, it is much better technology than the legacy stuff. At least with receivers like these, we can get by with bandstacked lnbs. EB
    We are working on adding support for bandstacked LNBF's in a future firmware update.


    Best regards,

    PwrSurge
    AzBox Canada
    Reply With Quote
     

Page 2 of 3 FirstFirst 123 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •