Aiuto!! il mio hypercube si è bloccato :(

Aiuto!! il mio hypercube si è bloccato :(:bowdown:
Chi può aitutarmi, ho provato la procedura con ipterminal ma non ci riesco

???
Hello!
English language would help.

Hi, I have problems with my Decoder box Hyperbox - Enigma2 hypercube, I did all the procedures du upload files uboot_repair_hypercube, as indicated, the decoder starts, then gives me the 'background image of the skin hyperon 3, and just, you stops there. I have to do, I tried to send the folder e2 from usb, nothing SKIP upwards wholly, BOTLOADER SKIP, ENIGMA2 SKIP, ANDROID SKIP.. Can you help me please? Thank you.:bow:

Try to install the attached file in the Hypercube.

Thanks, I'll try, the problem is that I always usb BOTLOADER SKIP, Enigma2SKIP , ANDROID SKIP, :computer-17: with the serial cable unboot load the file, but then always the same. grrr ... I would know what to do at the end of the file unboot until there but then I get there? I have to do?. Thank so much :thanx:

Try this: [Only registered and activated users can see links. Click Here To Register...]

Help me !!:break:
Starting Microloader ASM built on Jun 01 2013 17:41:07...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Found Internal Ethernet PHY on GMAC0....
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
starting UART boot ...
Setting up default ATAG list...
Jumping to Uboot .........


U-¨ë‹�2009.08-dirty (May 30 2013 - 14:40:29)

DRAM: 512 MB
malloc: Using memory from 0x04200000 to 0x04400000
GCS: Setup In ISA MODE
UART Boot not Supported .....
GCS: SFC DEVICE SETUP COMPLETE
Boot Device: SPI Flash
JEDEC ID = (0x1,0x2,0x15,0x4d,0x0)
JEDEC ID = 0x10215
s25sl032a (4096 Kbytes)
GCS: NAND DEVICE SETUP COMPLETE
512 MiB
In: serial
Out: serial
Err: serial
Net: lip0
Check if 's' or 'p' pressed: 0
Initialize USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Find valid fat partition 1
reading su980/upgrade.scr

** Unable to read "su980/upgrade.scr" from usb 0:1 **
CCC

Starting Microloader ASM built on Jun 01 2013 17:41:07...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Switching to 'C' code...
Starting Microloader C...
Found Internal Ethernet PHY on GMAC0....
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
starting UART boot ...
Setting up default ATAG list...CCCCCCCCCCCCCCCCCCCCCCCCCCCCC
Jumping to Uboot .........

U-Boot 2009.08 (May 03 2013 - 16:10:34)

DRAM: 512 MB
malloc: Using memory from 0x04200000 to 0x04400000
GCS: Setup In ISA MODE
UART Boot not Supported .....
GCS: SFC DEVICE SETUP COMPLETE
Boot Device: SPI Flash
JEDEC ID = (0x1,0x2,0x15,0x4d,0x0)
JEDEC ID = 0x10215
s25sl032a (4096 Kbytes)
GCS: NAND DEVICE SETUP COMPLETE
512 MiB
In: serial
Out: serial
Err: serial
Net: lip0
Check if 's' or 'p' pressed: 0
We get key s
Initialize USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 4 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Find valid fat partition 1

** Unable to read "su980/upgrade.scr" from usb 0:1 **
************************************************** **********

Quote:

---

** Unable to read "su980/upgrade.scr" from usb 0:1 **

---

Try a different usb pen Or usb port.

Thanks a lot, I have tried it with a 3 different usb pen, and the problem that I always usb BOTLOADER SKIP, SKIP Enigma2, ANDROID SKIP, with the serial cable load files uboot_repair_hypercube, everything perfect, but then always the same. or file not found, tried with E2 folder, I tried with su980 folder with files scr upgrate and then inside the folder E2. I do not understand what to do, I've done hundreds of tests. I hope someone can help me. thank you